Waleska GA Electrical Service And Repairs

Flooring company removed the toilet in the upstairs hall bathroom to install new flooring. The toilet was installed incorrectly which caused a leak in the ceiling of the kitchen. I reset the toilet with a new wax ring and bolts. I sealed around the base with clear silicone. The toilet has been tested thoroughly. Thank you for choosing TE Certified!

Today we were called out here because Lisa discovered a leak coming from one of the shark bite fittings that was put in when work was previously done to the home from a contractor. The fitting that I noticed was a gray polybutylene to pex adapter coupling. The pecks pipe was connected to the gray polybutylene side of the coupling was the reason why it was leaking to begin with because it’s not the same diameter as for the pecan piping. I recommended to get rid of the shark bite fittings because they are temporarily and not permanent fittings. Lisa agreed to replace them and also swap out the PRV that they are having pressure issues. I replace shark bite fittings with proper pressed fittings that bond better to the pipe and swap out PRV with new main shutoff. Turn the water back on to test the fittings that I have put in for any leaks and found no issues. We are also here for today and there are no other plumbing concerns.

Arrived to finish up rough

Arrived on site and customer stated that the one of the water heaters T&P was popping while inspector was walking through the house, and requested homeowner get T&P replaced. Water heaters were installed in 2023. Everything around the heater was functioning properly. Pressure was 60 , expansion tanks was filled with air, and gas control valves were in normal sequences.

Installed can lights on porch with fan. New sconces roughed and roughed in outdoor outlet

Service visit on Generac 22kw standby generator

Installed customer supplied motion sensor light switch in the laundry room Rerouted low voltage wires for stereo system on the mantle in the living room through the fireplace Pulled power off TV receptacle for a receptacle and switch on the bar top. Pulled a switch leg for a 4 inch waffer over bar top. Replaced a Dual Function Siemens breaker for a AFCI breaker due to the treadmill causing the breaker to trip. We informed the homeowner that the treadmill should be on a dedicated 15/20a circuit.

For this job the customer stated they had a disposal that was making a loud humming noise and the impellers were not working. Further inspection showed a sink that was slow to drain due to the disposal being clogged and non operable. I recommended replacing the disposal with a new more powerful one. The customer agreed and the old disposal was removed and replaced with a new 1/2 hp badger disposal. After disposal was installed I tested it multiple times including filling and draining the sink as well as running the dishwasher. No leaks were observed and the disposal was in proper working order.

Arrived on site and completed propane connection for the customer generator . We originally tried to fire up the unit but customer stated the electrical department is coming out to finish the electrical and test fire the unit

System inspection completed. Filters replaced. Drain line cleaned. No immediate issues noticed. Cycled power for 10 minutes to read the communication glitch. Discuss findings and enhancement options. System cooling properly at this time. Thank you for choosing TE certified!

Arrived on site and customer stated a leak as coming from the meter . Customer agreed to have me dig up and locate the leak to determine the issue . Once front of the meter box was cleared , and found a check valve leaking. I had to cut out the check valve all the way back to the meter to make the repair.I replace the meter nipple , check valve and replaced the ball valve that was on the line . Once repair was made I turned the water back on at the meter and checked my repair are to ensure no issues . Water is back on to the house and pressure is 60. Additionally I left quotes to repair the hole water line .

The living room outlets left and right of the fireplace were not working. The issue was due to a toggle switch located on the foyer area being turned off. As a courtesy we bypassed the switch for the come owner allowing for constant power to the outlets. We also found that plug mold and wiring was installed improperly to the right of the fireplace we left an estimate for the correction.

Wire in and install a new location outlet in the closet near the living room Interlock kit that we provided was the wrong interlock kit will have to return to install interlock. Oil was provided by customer and we poured oil in generator. Made sure generator was hooked to generator outlet and hooked up to generator.

Arrived on site and customer had a toilet in the downstairs bathroom that needed to be reset and the flange needed to replaced. I cut out the Brocken flanged cleared debri , set a new wax ring and bolts and reset the customers toilet. Toilet is back up and fully functioning.

Complete the following work: Remove the (2) existing flood lights located front left of home at soffit and back right of home on soffit and install a new customer supplied floodlight with security camera. Wire in (3) new location flood lights with attic access for the back left of the home in soffit, front right and back right of home. This will include a power supply, boxes wiring, and positioning the cameras per customers request Install (2) customer supplied motion sensor switches in the pantry and laundry room

Replaced kitchen recessed lights with new integrated recessed trims. We replaced 6 bulbs in the master bathroom with new customer supplied bulbs. We also added a new outlet in the master bed closet. The homeowners are happy with the 3000k color on the kitchen lights. I also discussed installing a whole home surge protector at the main panel and replacing their expired smoke detectors. Everything is working upon completion. We need to main over the invoice, estimate, and warranty info

Installed a customer magnetic dual slide bar combo shower head in the master shower. After shower head was installed I tested the shower head to ensure proper functioning. Customer has no email .

The threads of the existing home spigot were damaged and causing a leak. Installed new hose spigot. Cut open an 8”x8” hold inside of the garage to gain access to the pipe. Cut out the old spigot and the elbow in the wall and replaced with new pex fittings. Thank you for choosing TE Certified!

Replace busted water main through foundation wall where xfinity hit water main, and reconnect to water main inside

Completely diagnosis and repairs of tripping dual function bresker

The customers had bought the home and the inspector had flagged an issue with a double tapped breaker inside the panel. I came out today and completed the following work to correct the panel: Removed the 20 amp single pole breaker from circuit # 18 and moved it to #5. By doing this it had eliminated the non listed part. Installed a pre existing 20 amp duel function breaker on to #18 Removed the double tapped wiring on the circuit breaker located on circuit # 7 and pig tail the wires together and land it back on the existing breaker. Cleaned all dust and debris out for the bottom of the panel. I removed the existing surge protector and supplied and installed a $75,000 lifetime warranty surge protector at the service disconnect with a new breaker. The reason for the replacement was due to the existing surge protector has 35kA (35,000 Amps) of protection with a 3 year warranty (expired) with $10,000 of protection coverage.

Upon arrival, I met with the owner. Their kitchen sink recently started backing up but does slowly drain when the water is shut off. We discussed the options and today they are moving forward to Hydrojet the line. There is a test cap on top of the santee they allowed me to saw off for access. They will cap it off when I am done. I first ran my flex shaft to clear the blockage and help break up debris standing in the line. I then ran my hydrojetter, performed several passes to ensure the line is cleared. I ran the faucet as well and ensured no leaks or errors. Perform sink drain line cleaning using hydro jetter. Drain clear only. Does not include repairs or main line cleaning. No warranty on drain cleaning.

Install new outlet in basement

Full system

arrived on site and customer was experiencing a dripping faucet in the upstairs bathroom. My first step was to check the pressure of the house which I got a reading of 50 psi while diagnosing the pressure. We ran a faucet in the house and while the faucet was running, the pressure dropped by 12+ psi. Customer was experiencing pressure regulator issues, which was the main cause of the cartridge failing. I also noticed that the tankless water heater had no thermal expansion tank. The cartridge was a special type, which customer wanted to replace the cartridge initially , however we could not identify or locate the valve type . I also noticed that underneath the bathroom faucet cabinet there were no shut off valves. Customer stated that they did not use that bathroom faucet and just wanted to isolate the bathroom faucets. Customer agreed to remove the backing and the drywall underneath the cabinet and installed shut off valves for the bathroom fixture, which I was able to stop the dripp