Fairburn, GA Electrical Service And Repairs

Replaced bad GFCI on the right side exterior. Light was flashing red on GFCI.

No cooling call, upon arrival customer stated that system was frozen yesterday, filters were dirty, replaced 2-16x25x1 filters, cycked system on and checked refrigerant levels, subcooling is running at 13.7 degrees Freon levels look good, opened and closed both dampers, dampers are operating properly at this time, changed damper settings to 1 from 0 to get some air to bleed through the system when one zone closes, blower wheel is a little dirty, compressor is overamping recommended hardstart kit to help lower amp draw on startup, replaced 70/7.5 mfd capacitor with turbo 200X, recommended TE standard flood protection to help prevent any water damage from occurring, flushed drain line, also recommended UV lights to help improve indoor air quality. The reason for unit freezing up is likely due to having a dirty filter and damper settings, however there may be intermediate issue with system, customer will call back if they have any further issues, also recommended using less restrictive fi

Installed a new Gen 3 Tesla Charger on a dedicated 60 amp circuit from the main panel for a 48amp charge rate.

Replaced light fixture with ceiling fan in living room and upstairs front bedroom.

Performed diagnostic on 6yr old Goodman at unit with a 7yr old Goodman furnace, upon arrival customer stated unit has been freezing and not cooling properly, checked tstst already in ac mode, customer stated she just turned it on, checked filter, customer had filter in return vents, explained filter don’t go in vents, she stated she couldn’t open the filter door, upon goin in attic noticed they masking then door shut, used my knife to get it open, customer can now put correct size filter in proper location, filter size is 16x25x1, noticed unit has no flood protection in secondary drain pan, recommend wet switch to prevent ceiling damage, inside furnace is heavily impacted with dust and debris, blower wheel and motor heavily covered, recommend pulling and cleaning blower wheel, explained with cleaning motor can still fail, inspected evap coil, coils has signs of rust, evap coil heavily impacted, explained coil would need to be cut out to clean properly, recommended removing and cleanin

Installing 4 GFCI outlets and running a new line for proper grounding to garage outlets

For this job, I conducted leak detection services inside of the home for original technician Keith. Investigation, I noticed that the meter only ran when the hot side was open and stood still as soon as I close the intake on the cold side of the water heater. I introduced compressed air via the washer box on the hot side and used ground sonar to discover that the leak is directly underneath the water heater/under the slab/location has been shared with original technician Keith, who is on the scene.

Installed 2 customer supplied shower bases in basement and installed shower drain and drain branch arm for upstairs master shower.

Replaced seats and springs in the hall bath tub shower valve, recommend replacing the valve

found that the master bathroom, toilet supply line and busted and customer turn water off to toilet. Performed minor rebuild on toilet to repair the issue and prevent other parts from failing in the near future. Replaced fill valve, flapper, supply line and angle stop due to the supply line being made onto the old stop. Turn water back on and tested and found no other leaks at this time. Water pressure was at 50 psi

No cooling call, upon arrival systems pressures did not look good system was running 55/310 with a subcooling of 5 degrees and a superheat of 90 degrees, system has liquid line restriction, there is no filter drier installed inside of system, filter drier is used to filter out moisture inside of the system, quoted replacement of TXV and filter drier, also quoted liquid line service valve found loose connection, tightened nut going to service valve and system stopped leaking, after TXV and filter drier are added to system we will pressure test system at 350 psi to ensure that there are no leaks inside of the system, emergency drain pan is also not big enough to cover below air handler, system is also low on airflow on both the return and supply side only has about 2 tons worth of ductwork needs 3 tons of ductwork, recommended install supervisor to come out and quote replacement of ducts/adding ducts as well as quote replacement of emergency drain pan. Customer will review estimates and

No cooling call, upon arrival system was not running, outdoor breaker was in the off position, checked refrigerant levels and found that system was running 229/287 with a subcooling of 1 degree and a superheat of 16 degrees, compressor is not compressing refrigerant, Indoor TXV is also stuck in the open position, filter was last changed June 2024, system not being maintained is likely the reason on why compressor and TXV have failed, condenser coil is also dirty, dual capacitor is also bad reading out of tolerance, customer stated that she would review estimates and get back with us as far as repairs goes.

Replace light fixture with ceiling fan in living room

Upon arrival, I performed a complete diagnostic of the second-floor air conditioning system. The system is a 2018 AirTemp 3-ton R-410A split system equipped with an indoor TXV metering device and services approximately 1,500 square feet of the home. The return duct system consists of two 20-inch flex return ducts, which is appropriately sized for a 3-ton system and appears capable of providing the required airflow. During the electrical inspection, I found the compressor operating at 8.85 running amps, which is within the manufacturer’s rated load of 13.6 RLA, indicating the compressor is currently operating within its normal running range. The contactor tested within manufacturer specifications; however, the dual-run capacitor tested out of range and should be replaced. I also recommend installing a compressor hard start kit to reduce startup amperage, minimize electrical stress during startup, and help extend the life of the compressor. The condenser coil, evaporator coil, and blow

We arrived today agent explained to us that he needed a new ring floodlight installed on the front of his house. The ring floodlight is power from an upstairs bedroom and receptacle. We installed the new ring, floodlight directly over his garage door and wired everything in. Once power was installed the ring floodlight worked properly. It was great seeing you again, Adrian! If we can help you with anything else, please feel free to call me anytime.

Installed customer supplied bathroom bidet and relocated water line in ceiling below. Tested and inspected. No leaks and working properly.

No cooling call, upon arrival customer stated that system was not cooling only blowing out hot air, checked capacitor and found that capacitor was reading 0 on compressor side, compressor is also overamping, recommended hardstart kit, refrigerant levels are also low, zone board is not wired up properly, also does not have secondary transformer, zone board may be bad however we can try and rewire zone board first and add secondary transformer to system, recommended nitrogen leak search, system is cooling however system is not cooling very effeciently, customer understands that there is more work that needs to be done quoted repairs customer will call us back when she is ready to move forward with repairs.

Call out for toilet constantly running gave estimate to do rebuild on toilet and upstairs hallway bathroom and to replace PRV customer agreed gave second toilet rebuild as a courtesy. We removed the old flappers, fill valves, and supply lines on both toilets the upstairs hallway, bathroom, and the downstairs hallway bathroom installed new parts also removed and replaced the PRV tested no leaks and working properly at this time.

Performed diagnostic on 20yr old upstairs amana unit, upon arrival customer stated unit stopped cooling, checked tstst, cycled to ac mode, went to attic to inspect unit, noticed unit has no flood protection, recommend wet switch to prevent water damage to ceiling, checked filter, unit has a new gas valve , inducer motor is heavily rusted, checked blower wheel, found impacted, recommend pulling and cleaning, explained blower motor can still fail, blower motor pulling higher than normal amps, recommend replacing blower motor, evap coil heavily rusted, explained can start to leak at my moment, upon checking outdoor unit, found compressor running but not condenser fan motor, checked contactor, capacitor, found bad capacitor, recommend replacing to continue diagnostic, customer approved installed new 35/5 capacitor, unit started up, checked amp draw, compressor is over amping on start up and only pulling 2.7 amps on RLA, tried to pump refrigerant back into compressor to verify compressor is

Trouble shoot issue with the upstairs tub shower and provided options to repair, replaced the tub spout and tested the shower

replaced the 40 gallon gas water heater in the garage with a new 50 gallon gas water heater, added an expansion tank and secured to the wall, replaced ball valve and gas whip,

Add studs and replace drywall. Tape seams. Multiple coats of joint compound. Sand. No painting.

Today we replaced the ceiling fan in the living room, a beautiful black fan was installed with black blades facing down. I also installed the mount for the remote on the wall near the thermostat

Today to solve the humming pipes and leaking shower, we replaced the PRV and also replaced the fill valve in the toilet that was damaged due to the pressure issue

Performed diagnostic on 10yr old Lennox heat pump, upon arrival customer stated unit has been out about 3 months, checked both tstats, cycled to ac mode, went to attic to inspect unit, noticed secondary drain pan heavily rusted, recommended wet switch to help prevent water damage, checked blower wheel, blower wheel impacted, recommend pulling and cleaning, blower capacitor checked ok, evap coil heavily rusted, upon checking outdoor unit found not running, system giving code for low pressure switch, reset unit to clear code, unit started up, pressures showing low on refrigerant, no signs of oil, explained to customer we would have to perform a leak search to locate leak for additional repair cost, customer did wanna move forward with leak search, upon starting explained to customer I would have to cut top bars of cage off due to its just a welded cage with no way to open it to access inside of outdoor unit, customer didn’t want me to cut cage, customer wanted to hold off on leak search