Oxford GA – Electrical, Plumbing & HVAC Service and Repairs

I worked on replacing existing hose Bibb ball valve shutoff under master faucet and also replaced customer supplied kitchen faucet

Called out to reset toilet. Replaced wax ring and installed new bolts. Set the toilet back with new China caps and connected the water supply. When testing the toilet, it did not flush properly. Ran closet auger through the toilet to clear the toilet of any blockages. After doing so the toilet was tested thoroughly with and without paper, and is now flushing properly and draining as it should. Thank you for choosing TE certified!

For this job i worked on capping off an old gas line running to the deck and also adjusted gas line to the stove with new gas shut off valve to make it flush with kitchen wall

Troubleshoot on partial lost of power in home, provided options to repair, futher diagnosis from power company is required

Repiped whole home water lines, replaced all angle stops and replaced all supply lines (except for the kitchen faucet).

Install 3 new pendant lights and one new chandelier Install cs dimmer

Replaced PRV, main shut off valve, and the hose bib shut off valve

Took out existing water heater and installed brand new 80 gallon hybrid electric

Today I installed a new 50-gallon electric Rheem water heater in the back room closet of the home. After installation, the homes water lines were purged, and all connections were thoroughly inspected for leaks. The home is supplied by a well system, and the water pressure was tested at 60 PSI, which is within an acceptable range. At this time, the new water heater has not been energized because the home is currently undergoing an electrical panel replacement. The electrician is scheduled to complete the panel installation and restore power tomorrow, at which time the water heater will be connected and placed into service.

Today we are called out for a leak in the ceiling and a high water pressure, performed leak search and could not replicate any leaks, upon when washing machine was ran water would pool out of the front of the machine. Also replaced the Apollo PRV for a new Watts professional model PRV

Figure out why fan has stray voltage Switch replacement and fan tap Install new, dual function breakers in replacement of bad arc fault breakers , install new breakers in replacement of mismatch breakers , and oversized, new lug for sub panel neutral, Splice 4 existing circuits into two and replace two breakers, with whole home surge protection

Today we did a spot repair on the main service line, repair was made on 1 inch pex and removed a failed sharkbite fitting.

Performed diagnostic on 21yr old Lennox heat pump for master bedroom, upon arrival customer stated he just moved in and was having some work done and noticed unit was cooling properly, checked tstst, cycled to ac mode, went to attic to inspect unit, noticed a lil water in secondary drain pan, recommend better flood protection such as wet switch, replaced customer provided filter, noticed unit has a ADP coil installed in back in 2017, but original unit is from 2005, blower wheel impacted, recommend cleaning, recommend replacing blower capacitor reading bad, evap coil starting to rust, recommend updating drain line as it’s not properly installed for heat pump operation, next inspected outdoor unit, noticed coils are impacted, recommend chemical cleaning, explained pressure are not gonn be accurate and will read higher due to dirty coil, check capacitor, contactor, checked amp draw, compressor over amping on LRA, and pulling higher then normal on RLA, let unit run for 15min to check press

Customer has 23 y/o Armstrong Air system that operates for main level. System is not cooling due tripped breaker caused by bad compressor. Amp draw on compressor very high caused by overheating. Condenser coils are damaged. Condenser electrical components are bad. R22 based system. Furnace has significant rust. Blower wheel is dirty. Run capacitor is bad. Ductwork is insufficient for system size. No water protection present. Informed customer of all findings. Advised customer to seek options for system upgrade.

Troubleshoot

Performed diagnostic on 12 yr old Lennox unit on right side of home, upon arrival customer stated unit wasn’t cooling properly, checked tstst, already in ac mode, went to attic to inspect air handler, checked filter, recommend TE standard flood protection such as wet switch, checked blower, evap coil heavily rusted, inspected outdoor unit, coil clean, capacitor and contactor checked ok, upon checking pressures and temp split, unit showing low on r410, the person who put the units in added r410 about a yr ago, gave option to perform leak search, customer declined, also gave option to add r410, customer declined all options, stated he will call the person who put them in, explained unit is not working properly and can cause other issues