Lilburn GA Electrical Service And Repairs

Performed work

Install grounding system by driving two ground rods running 4 AWG ground wire to five feet of water entrance to the home, a bonding jumper at the prv, a bonding jumper on the hot and cold water lines, and a utility interconnect bonding bridge. Install whole home surge protector in main panel with a flush mount kit and new breaker

Install whole home surge in main panel with flush mount kit and new breaker Customer experienced a surge due to an issue on the power company pole. This surge affected the refrigerator, light bulbs throughout the house, and the thermostat. All of which will need to be replaced/repaired

A phase 120 B phase 120 C phase 208 Sub panel voltage is A phase 120 B phase 208 Customer needs 120 on A and B phase in sub panel Rerouting breakers and wiring to make existing system work. ***No warranty on existing electrical system*** #7 and #9 new sub panel #1 and #28 other relocated circuits Sub panel is 120V A and B PHASES PER CUSTOMER AND GAS REPAIR COMPANY.

During today’s visit, we inspected the internal parts of the faucet to determine the cause of the issue. The faucet uses an older internal valve stem that is no longer manufactured. Because of the age of the faucet, replacement parts are very difficult to find and repairs would be unpredictable, with a high risk of continued leaking or Future failure. For this reason, repairing the existing faucet is not recommended, and faucet replacement would be the most reliable long-term solution. In addition, we evaluated the Home’s water heater and noted that it is approximately 20 years old. While it is currently operating, water heaters of this age are well beyond their typical life expectancy and may begin to fail without warning. Due to his age, there is an increased risk of leaks or loss of hot water, and proactive replacement should be considered to avoid potential damage or unexpected downtime. All findings and recommendations were reviewed with the homeowner, and options were discussed

Replace tank water heater with tankless.

Customer has 20 y/o Gibson system that operates for main level. System is not heating due to high limit tripping caused by compromised heat exchanger. Found very dirty filter. Poor water protection. Blower wheel dirty. R22 based system. Informed customer of all findings. Advised customer to seek options for system upgrade.

•New 4-wire (modern) dryer circuit •GFCI breaker (shock protection for dryer) •New Dryer Outlet+Box

Replace various light bulbs and flood light

Inspection today on furnace. System is in good condition and adjusted low stage heating in gas valve to 116 degree vent temperatures. Checked calibration of thermostat.

Perform a systems home care maintenance. Change filter, tested all electrical components, flushed drain line, tested thermostat, Tested both system on cool and heat, checked pressures and refrigerant. System is working properly at this time, however notice biological growth is spreading around duct work, highly recommend to add a germicidal device to the unit to stop the spreading and purify the air. Costumer decided to move forward with repair and enhancement. Work was done and tested. Thank you for choosing TE Certified,

Spot repair with ZERO WARRANTY

Troubleshoot

Storage room switch

Testing system not heating for the entire clubhouse. Found that the unit was not getting power in from the stack switch. Today we went ahead and replaced the stack switch and the system is working with no issues at this time.

Te certified will use a sewer jet to temporarily identify the remaining run of the pipe to possibly offer a rerouting option

For this job I came to see why customer was not getting hot water. I found that the connections on the water heater were faulty and not getting electrical current to the water heater. I re stripped the wires and added new wire nuts to make connections. After that was done I was getting proper electrical current to the unit and it fired up. Tested and left work area clean.

Run cable machine inside cleanout Customer was experiencing main line backup affecting whole house. We ran k750, brought back roots. Clearing was successful and we setup camera inspection. Customer had partial mainline repipe done by other company but did not solve root issue.

Replace a 15’ section of 3” ABS drain pipe in crawl space due to a significant belly which is causing water to accumulate and clogs to form.

Estimate to replace full service line

Replaced all of flue pipe, tested system and everything ran great. System ran without any error codes. Temperature went up on thermostat. Opened doors to room upstairs to help circulate air flow better and that helped a lot for system. Will return to install the flue temperature sensor when it comes in.

The bare minimum basic repairs to get the system running today were completed.

Run 400 cable and clear blockage, set toilet on new wax ring Camera inspection follow up Customer was having mainline blockage affecting toilet,sink,washer, and kitchen sink. The other fixtures were draining fine because they were tied on a different stack. Ran k400 in drain and were able to clear blockage. When testing washer machine a little amount of water would push back but then drain immediately, possible slope issue. We left toilet off for camera tech.

System was heating upon arrival. Customer stated she had issue with program on the thermostat but she figured it out. I offered thermostat replacement options and we went ahead with basic thermostat today. Also looked at filters while we were here and all 3 needed changed. Offered maintenance plan. No failures at this time.

Came in today for a no heat call. When testing main floor system found that igniter had failed and inducer motor is constantly cycling on and off causing hitting mode to fail. Proceed to also test heating for upstairs system, considering that furnace are the same years old. Also found that upstairs system inducer motor is on his way out and igniter will proceed to fail right after. Let costumer know and presented options also giving the option of furnace upgrade. Thank you for choosing TE Certified!