Jasper GA Electrical Service And Repairs

Remove old high bay lights and replace with plug I’m led ufo high bays. The new lights are 120, so we will add outlets to the junction boxes for the lights to plug into

Connected a customer provided natural gas space heater, located on the back patio. THANK YOU for trusting T.E. Certified!

Performs 2 system Homecare maintenance today. Both filters were replaced today. Drain lines have been flushed and confirmed to be clear at this time. All systems operating parameters are within range at this time in both heat and cool modes. No concerns to be reported.

Finish panel replacement job

Replace main panel inside of home refeed the service wire to panel from age and redo grounding system

Replace 50 gallon gas water heater

Arrived on site and customer stated he did not have hit water coming through the shower valve, but everywhere else in the home had hit water. I turned on shower handle all the way I the left and water was hot immediately. No issue with customer shower . However customer stated he had issues with the toilet not flushing and filling properly , so he decided on me doing a rebuild on the toilet. Toilet is up and running with Replacment parts.

Trouble shoot lights in bedroom

Arrived on site to install customer supplied garbage disposal under the kitchen sink. Kitchen sink did not have an existing disposal prior to, so electrical ran power and a switch. I then installed the disposal

We will install a switched outlet for the disposal and a whole home surge protector

Replaced bath fan and triple switch with a stacked switch

Troubleshoot a bath fan not working. Determined it needs to be replaced. We are replacing the fan on Wednesday the 7th

Troubleshoot gfci outlets not working

Run a new dryer circuit from the panel and set a new outlet

Arrived on site to perform a troubleshoot on the microbe and fridge not working. Upon inspection, we noticed the GFCI outlet that was installed was not installed correctly. Once we bypassed the GFCI outlet, we noticed the outlets were reading open neutral. We opened the microwave outlet and noticed the neutral and an hot conductor was damaged. We installed a new outlet for the microwave in the kitchen. We also installed a new GFCI outlet for the kitchen countertop. We discovered 14 gauge wire on this circuit. 14 gauge wire is only rated for 15 amps. Upon further inspection the wire was not connected to anything so we removed the 14 gauge wire and kept it on a 20 amp breaker. I discussed other options with the homeowner about taking care of double tapped neutrals in the main panel as well as install dual function protection for all 120v circuits. The homeowner did not want to take care of this at this time. The panel that’s installed will not accept a main breaker. Everything is working

Arrived on site to perform work previously quoted. We provided and installed a new generator inlet by the meter on the exterior of the home. This is a 50 amp inlet on a 50 amp breaker. We provided and installed a new generator interlock kit. We also provided a new 50 amp generator cord. I walked through with the homeowner and showed him the steps to operating the portable generator. Everything is working upon departure.

Downstairs unit has a failed condenser fan motor. Homeowner will need to sign of on electronic estimate for the motor to be ordered. The motor is not in stock by rheem; may take approx 6 business days to get this motor in or longer (depending on rheem). Left power off to the outdoor unit with the homeowners permission. Homeowner not home; emailed estimate per homeowners request. Homeowner will need to sign electronic estimate asap to get the motor in, in a timely manner. Full diagnostics on system cant be perfomed until fan motor has been replaced; system may have additonal issues.

Customer said that he had water dripping from the bottom of the water heater. I found the siphon cap underneath the unit had a bad seal and needed to be replaced. I replaced the O-rings in the siphon cap as well as cleaned the filters and screens.

In the master closet from the 3way switch near the bathroom door drop down a new location outlet. The outlet is for a cloths iron and I looked at the u it and it has a 1400 watt output/11.7 amps on a 15 amp circuit. I informed the homeowner that this outlet is on with the master bedroom lights and outlets along with the master closet lights. I also let her know that a dedicated circuit is preferred in these circumstances but she opted out and will just be careful of how many things are on. A dedicated circuit would take quite a bit of drywall damage due to the second floor and the panel is in the garage. As a courtesy I installed a customer supplied motion sensor switch in the garage by the door going into the home, located in the 2g box, left switch

2018 Rheem 3 ton whole home system System is not turning on nor cooling Checked IDU for power, which had power, but was not running Noticed the blower wheel was slowly spinning, then stopping repeatedly Checked voltage from board to blower motor, which had proper voltage Blower motor is seized up due to the amount of hair and biological growth that is kicked on the wheel, making it very heavy, causing to the motor to seize up Inspected the evaporator coil, which had the same biological growth and hair kicked on that as well, causing that to not be able to have proper airflow Air handler itself has a severe amount of biological growth all over the wires the cabinet the components which is a health concern and would need to either be deep, cleaned or replaced Blower motor will have to be ordered after talking to supply house as well as the wheel Informed homeowner that if we install a new blower motor and wheel without doing a deep clean and putting UV light in air handler we will not be

Installed new trim on the master bathroom Roman tub. Customer provided the new Delta trim. Thoroughly tested the new trim. Thank you for choosing TE Certified!

Installed new 50 gallon electric Rheem water heater. Installed new ball valve and expansion tank. Water heater is sitting in an aluminum drip pan. Allowed the water heater to fully heat and tested fixtures. The kitchen sink had almost no water flow from the hot side. Customer had a new faucet on hand so I installed that as a courtesy. Thank you for choosing TE Certified!

Arrived on site and met with the housekeeper, homeowner was not present . I spoke with the housekeeper and she did state that she was the one who noticed a stain at the bottom of the cabinet. During my troubleshooting, I opened up the angle stop to the hot side , as it was shut off , and ran water to the sink for 40 minutes. I found no signs of water coming from the shut off valve, bathroom faucet , supply lines, sink, or drain during that time .

Came out today to install new 40 gallon electric water heater. Removed existing heater from the system and installed new heater in a pan with a water alarm. Installed new piping, new shut off valve and new thermal expansion tank mounted to a bracket. Sleeved electrical connection and connected electrical whip to heater. Insulated piping, added valve tag and bonding clamps. All work was tested. Verified power to the unit.

Replaced system for whole home added 5 inch media filter redid the flu all to double wall