Hampton, GA Electrical Service And Repairs

Completed all approved work. Tested and everything is working great with no leaks. 1- expansion tank rusted and starting to leak and not mounted to bracket 2- PRV is worn out causing high water pressure and squealing from showers 3- leak on cpvc female adapter below main water shutoff valve 4- hole in kitchen drain vent pipe and in kitchen sink waste tubular pipe 5- hall bathroom tub drain is broken 6- hall and master bathroom lavatory sink stopper connecter rods are broken

Today I installed a outlet near the garage door for the new opener, installed a floodlight on the back of the home

Installed a 50 gallon gas water heater fully up to code. Rebuilt two sink wastes. Replaced loose tub spout in guest bathroom. Homeowner is happy; every has been tested annd inspected. No leaks at this time.

Performed diagnostic on 13yr old unit, upon arrival customer stated unit don’t feel as cold unless she drops temp all the way down, checked tstat, set to 73 reading 73, temp set to not go below 70, changed to 60 to be able to check system, cycled to ac mode, unit started up, checked filters, unit has three pleated filters, filter at furnace was last replwced 12/25, other two filter had date to replace 8/26, removed filter at furnace , explain filter is not needed with other two filters, replaced customer supplied filters, inspected furnace, recommend better flood protection such as wet switch to prevent water overflow, blower wheel impacted, recommend pulling and cleaning blower wheel for better airflow, blower capacitor check ok, inspected outdoor unit, found coil heavily impacted, recommend chemical cleaning coil, checked capacitor and contactor, contactor starting to burn and pitted due to high amps, recommend replacing contactor,compressor over amping on LRA 85/77, recommend hard

Repipe of home

Customer has a high water bill upon arrival, checked all fixtures and seen that the meter was moving at a high rate, isolated the inside of the home and check the meter and determine the leak is still inside in the slab recommended leak detection and provided options for repair

Today I replaced 2 gfci outlets with customer supplied outlets along with installing a whole home surge protector.

Today as I arrived back. It is September 22 at 9:30 AM. I removed the existing severely burned disconnect controlling power to the upstairs furnace. I replaced it with a new disconnect and made all wire connections inside. I also installed two Polaris lugs on the wires inside of the furnace to replace the incorrect UL listed wire connections. Once all connections were finished, I engaged power on the unit and it worked properly. When I left both upstairs and downstairs were blowing cold air out of the vents. The downstairs thermostat is set to 80° and the upstairs is set to 81° cooling. If the AC unit starts having issues blowing out cold air, please contact us again and we can send out one of our HVAC technicians to perform a troubleshoot to see what’s going on with it. In every case when there are severely burned wires and disconnects like this, you could always have an electrical surge that has potentially damaged the unit causing problems eventually. If you have any questions abo

As I arrived today, it was explained to me that power has been off to the house for close to a week. After opening up the electrical panel in the garage and also opening up the meter base on the outside of the house where power comes in from the power company. I found the main master breaker in the meter base was tripped. I turned all of the breakers off and the electrical panel in the garage and I reset the main breaker at the meter base. Once I did that, I went back into the garage area and started turning on each breaker one by one until I got to the 60 amp furnace breaker. Once that was turned on that breaker it kicked back very hard tripping and also tripped the main master breaker in the meterbase again! Once I got into the attic space to examine the furnace I found the disconnect controlling power to the furnace was damaged severely. Inside furnace disconnect, I found severe melting and wires that have been touching to the point where they arched out and blew holes in each oth

As I arrived today, it was explained to me that the breaker controlling the 20 amp circuit I install installed Monday installed directly below the electrical panel tripped a couple times after the refrigerator was plugged in. I removed the dual function breaker and installed a standard breaker for the 20 amp circuit. I also then removed the standard duplex receptacle and installed a GFI receptacle in its spot which is all that is required in a garage. All votes are normal on the circuit and all equipment is in good shape along with all connections being tight. While I was here, I also installed a customer supplied ceiling fan in the master bedroom. Once the existing fan was removed, I installed the new one. Made all connections and the ceiling fan worked properly. It was great seeing both of you again! If I can ever help you with anything else, please feel free to give me a call anytime. Thank you, Brandon

Customer stated the newer disposal was jammed, upon approval, unjammed the disposal and removed glass debris, washed down the disposal and tested several times, filled and dumped the sink while running the disposal.

As I arrived today, it was explained to me that the garage GFCI receptacle keeps tripping when the refrigerator is plugged into it. The refrigerator worked fine in the kitchen area where it was plugged into. Everything in the garage along with the kitchen, lights, hallway, lights and guest bathroom or also on that same breaker. I’m installed a new 20 amp dual function breaker in the electrical panel and directly below the panel install installed a new duplex white receptacle. To make space in the electrical panel for the dual function breaker I had to put a 15 amp tandem breaker. Once all of this was done the receptacle and breakers worked properly. I was also shown a fan upstairs in the master bedroom that was not working. The light on the fan would work properly, but the fan would not. Both switches were functioning properly along with power at the fan. The fan itself is defective. I have attached an estimate to replace the fan and also install a metal rated fan box if there is not

You have several double tapped neutrals that need to be separated along with wires that need to be phase to the correct color Replace rear sconce light with customer supplied camera light We would add a light to the front of the home near the garage

No Cool Diagnostic Summary Came out to a no-cool complaint and found the system actively freezing up during operation. This is a 2021 Carrier CH14NB024-A, 2-ton R-410A heat pump. After going through the system, I found several conditions that are affecting cooling performance and placing additional stress on the equipment. On the refrigerant side, I measured only 1.5°F of subcooling, while the manufacturer calls for approximately 11°F. With the system freezing up and the charge readings this far below target, the system appears to be low on refrigerant. I also observed residue around the outdoor service-valve area, which makes that area suspicious for a possible refrigerant leak. I recommend performing a complete leak search before adding refrigerant so the source of the loss can be properly identified and repaired. The system was also operating without an air filter installed. Because of this, dust and debris have been allowed to enter the return side of the system. The evaporator

Customer experienced a power surge and is recommended to get a whole home surge protector and upgrade breakers.

Arrive to continue diagnostic on a no cool. After wiring up the unit correctly and inspecting and diagnosing the system I found that the blower motor is bad. The bearings have gone out. Further inspection showed that the zone board was faulty. With both zones off the board still calls for cooling in zone one causing the blower motor to continue running and not the compressor. Recommendations: – replace zone board – Replace blower motor. Transformer was also blown from previous text as well as the blower motor being bad so transformer also had to be replaced in order to finish diagnostic. Customer decided to have system straight wired and upon doing that the condenser did not cut on. Upon inspection I found that defrost board was burned out. Both the defrost board and the blower motor were replaced, unit was straight waited and system is now operating and cooling.

Single system Spring Maintenance. Completed the HVAC heating and cooling inspection checklist. I ran the system in heat and cooling for 30 minutes and the system is operating according to specifications. I flushed the drain line with two gallons of water. I added drain cleaning tablets and endure to the system to assure it’s draining properly. Please refer to my Inspection checklist for more details. All work as been completed and unit is operating to manufacture specifications.

Adjusted recirculating pump to get cold water and unclogged guest bathroom toilet. Tested good. Everything is working properly.

Replaced reversing valve on downstairs system, also replaced filter drier in outdoor unit, pressure tested at 350 psi, also pulled deep vacuum on entire system, added fresh charge of 8 lbs of R410A refrigerant, charged system up delta T temperature drop looks good, flushed drain line, all units and electrical components are working properly

Goodman AC with 90% Furnace

As we arrived today, it was explained to us that two receptacles in the house were having problems and even sparking a little bit. We found that the kitchen receptacle was burned pretty significantly on one side. They receptacle and the bedroom did not have any signs of problems, but it was stabbed in the back, which is not good. This is the receptacle that was explained. It would spark a little bit every now and then. We replaced the receptacle in the kitchen that was burnt and we went ahead just to be safe and replaced the receptacle in the bedroom and no extra cost. While we were here, I also talked to her about installing a whole home, surge protector in the meter base outside. This will help protect the house from surges from the power company and lightning. We installed the new search, protector, in the meter base outside. All receptacles and the service detector worked properly once they were installed.

No cooing call for both systems, found that both systems were leaking refrigerant, downstairs system was completely flat on refrigerant, found that reversing valve is leaking and will need to be replaced, quoted replacement of reversing valve, also found that upstairs system was low on refrigerant, leak searched system and found that scrader core in evaporator coil was leaking, replaced schrader core, leak searched Lineset with leak detecto did not find any leaks in Lineset, there is a small chance that Lineset could be leaking however we recharged system today and if refrigerant leaks out again we will quote Lineset replacement, delta T temperature drop looks good on upstairs system, repair for downstairs system is scheduled for tomorrow between 2-5PM

No cooling call, upon arrival customer stated that minisplit in basement was not cooling, checked filters and found that filters were very dirty, also found that system is low on refrigerant, Schrader core is leaking, system also has 40 amp breaker, there should only be 10 amp breaker installed, drain is not running outside, Lineset should also be on the exterior of the home, quoted replacing Schrader core, leak searching system, assuming that that is the only leak in the system there may be more than one leak in the system, outdoor disconnect is also not wired in, recommended correcting disconnect and running electrical whip to system. we will need to nitrogen leak searching the system to confirm if there are anymore leaks inside of the system, quoted repair, customer declined estimate at this time and will call back if they decide to move forward, system is not cooling at this time. Recommended replacing system to install the system properly, also so that there can be a warranty for

Performed diagnostic on 9yr old basement unit, upon arrival customer stated unit wasn’t cooling, checked tstst, already in ac mode, inspected furnace, no flood protection, recommend wet switch, upon checking outdoor unit found not running, no 240 volts, went to main breaker found tripped breaker label water heater, turned on breaker now getting 240, put disconnect in and breaker tripped, unit has incorrect size breaker, recommend correcting breaker size to 40, tested compressor, found grounded compressor with plug blew out, gave option to replace compressor, highly recommend install supervisor due to warranty and customer stated this unit has been giving them problems since day one, scheduled install supervisor for today, unit not working

For this job, I worked on replacing a regular light fixture for a ceiling fan. Replace the box with a fan rated box and mounted the ceiling fan.