Licensed Electricians, Plumbers & AC Repair Company in Atlanta

Upon arrival, customer stated they wanted to replace their faucet. Upon inspection, I found that the shut off underneath the sink where connected to the supply lines. I gave the customer option to replace the shut off as well as the faucet customer went with the option. I also brought up that there was no expansion tank and how that can be dangerous in your plumbing system. Customer is reviewing the expansion tank quote and will be proceeding at a later date with installing one. All work was tested no leaks and a very happy customer.

Installed Gfci outlet and bonded box due to customer wanting to replace receptacle only. Recommend a new circuit be pulled to supply proper grounding to receptacle.

Came in to running toilet in 1st floor half bath the toilet. The shut off was a multi turn and customer opted to replace that with a new 1/4 turn stop.

Troubleshoot outlets not working in basement (3) Replace faulty outlet in basement (1)

Completed system maintenance verified and changed filters cleared drain lines with 2 gallons of cleaner each. Checked all safety and components while maintaining the system take notice the following. Main level system does not have a drain line safety switch , the humidifier has failed. Recommend replacing humidifier and adding a drain line safety switch.. Upstairs system is needing the filter replaced 16 x 25 x 4 Honeywell. Spoke with customer about issues that came across. Customer has declined for humidifier and drain line safety switch and only wanted filter changed at this visit.

Troubleshoot why lighting and outdoor outlets aren’t working.

-Single stage air conditioner (outdoor) / Single stage, constant torque furnace (indoor).  -10 year parts warranty (20 years for heat exchangers on 80% furnaces)  -10 years labor coverage when a Home Care maintenance plan is held with TE Certified. Lifetime Craftsmanship.  -Removal and disposal of existing system.   -Permit fees are included, system will be installed to meet or exceed county’s codes.   -Cost includes all required material, tax, & labor. No further charges will apply.   -New drain pan, safety float switch, water safety and condensate pump (if applicable).   -New outdoor electrical disconnect and new pad for outdoor unit.   -New flexible gas line and hard pipe gas connection to furnace.  -Flush, Clean and Test Existing Line Set and Pull Vacuum to 500 Microns.   -Will recover existing refrigerant per EPA guidelines.   -Will complete leak check and system & system start up. .  -B

Customer has 5 y/o Rheem system that operates for main level. Furnace located in attic. Noise being heard was from media filter casing not being properly sealed. Corrected sealing at bottom of casing and inside. Advised customer to replace 16x25x4 media filter.

For this job, I replaced two outlets in the family room

upgraded your older 2-prong electrical outlet to a modern 3-prong outlet. Older 2-prong outlets lack a grounding system. This means they cannot safely handle modern electronics or appliances that require a three-prong plug, forcing you to use unsafe adapters. By upgrading this to a 3-prong outlet, I have ensured that the receptacle can now safely accept modern plugs.

Met with owner on site and went over the work being performed today I started in the basement ceiling. I cut out the existing stand pipe and inline p-trap for the kitchen drain. Ran new PVC into the cabinet with a cleanout and studor vent. I abandoned the cast iron drain, capped the outlet in the cabinet. Installed a new outlet waste and p-trap for the kitchen sink. Ran water to test and confirmed no leaks or errors. Showed the owner the final results and cleaned up the work spaces. Abandon the cast iron drain for left side of sink and tie into pvc drain for right side of sink. Reconfigure the drains under sink for this to work. In drop ceiling, remove ptrap since ptrap will be under sink. Provide a lifetime workmanship warranty!

Attempt to clear laundry drain blockage We came out today for a laundry drain that was experiencing a blockage. We ran our cable machine first in the washing machine drain and ran it full length. We felt resistance and was able to get past it. There is cast iron drain pipes present in the crawlspace and there is a spigot in the back yard that is damaged and leaking. We were unsuccessful with the cable machine and recommended a mini jetter and they agreed. We ran our mini jetter in the cleanout in the crawlspace and we removed any gunk/cast iron sludge. We had the property owner perform multiple quick cycle tests on the washing machine while we saw all the water pass by in the crawlspace cleanout. We did notice the cleanout in front of the yard and it seemed like there was water sitting at the bottom and we let the customer know about this. The customer is satisfied and thank you for choosing Te Certified.

Separate neutral, install ceiling fan and install a whole house surge protector

APCO-X Air Scrubber Installation – Service Summary Arrived on-site to install two pre-sold APCO-X air purification systems. Both units were successfully installed and secured according to manufacturer specifications. Following installation, I operated the HVAC systems and verified that both were functioning properly and within manufacturer specifications. I also informed the customer that both APCO-X units have been registered and their UV lamp replacements have been added to our maintenance schedule. The customer will be notified when it is time to replace the UV bulbs to maintain optimal air purification performance. Final Status: Installation completed successfully. Both HVAC systems are operating properly, and no additional issues were identified during the post-installation check.

The Moen cartridge in the upstairs bathroom, located in the first bedroom, was replaced due to the bathtub faucet constantly dripping. Even when the water is turned off completely, the faucet continues to drip over time. This has become an ongoing issue for the homeowners. The faucet was tested and checked to make sure there were no other leaks causing the problem. After checking the fixture, the cartridge was found to be the part that needs to be replaced. Installed a new Moen 1222 cartridge to address the constant dripping and allow the bathtub faucet to work properly again.

Customer scheduled to have shower repaired with CS parts. Conducted repair on shower and tested. Issue is still present on shower. Advsided to replace shower valve.

Customer reported a supply line leaking from his main floor bathroom, there is construction going on on his neighbors house and he had to shut the water off to his house at some point and the leak showed up after that. I test the pressure which is a 55 psi and recommended him just replacing the two shut offs that were regional to the house as well as supply lines. At the tankless water heater, I realized that the exhaust has the incorrect fittings and slope since it’s going downwards, customer is aware of the risks of that! All work has been tested no issues!

Performed a full HVAC inspection on all systems. Inspected thermostat operation, electrical components, safeties, capacitors, contactors, blower assemblies, evaporator coils, condenser coils, refrigerant levels, drain lines, temperature splits, air filters, ductwork, and overall system performance/operation. Verified proper heating and cooling operation at each system and inspected systems for any signs of airflow restriction, electrical concerns, drainage issues, or abnormal operation. Installed germicidal light for the US system. Thank you for choosing TE Certified. If you were happy with today’s service leave a review and share your experience with my service!⭐️⭐️⭐️⭐️⭐️

We are called out today because the homeowner had a light fixture replaced by us about a year and a half ago and the light randomly stopped working. Upon arrival, I performed a troubleshoot and narrowed it down to a bad switch. We replaced all the switches in the foyer switch box. At the time of leaving everything was tested on and working thank you for calling TE certified!

On today’s visit we came out on reports of several outlets and a fan not working. During my initial walkthrough I discovered an old ITE breaker in their GE panel. This breaker was feeding the sub panel and all circuits not working were coming from the sub panel. I discovered that whoever had installed the sub panel had trimmed the wires to make them fit the ITE breaker and the breaker was making poor connection with the bus bar. I replaced the breaker with a properly listed breaker, cut away the damaged ends of the wires and remade the connections. Afterwards all of the circuits previously off were irking properly again.

Customer has 11 gas lanterns, all with varying. Wear on the adjustment valves, and there are plenty of em that are unable to turn. Was able to find the gas shut off valve underneath the crawl space for the entire setup. I was able to find the replacement valve assemblies and customer agreed to our quote. I have the parch ordered and the customer paid a deposit on the parts. There is no known date of arrival for the parts for us. At this point in time. If the parts do not arrive before the nineteenth, then we will more than likely have to schedule after the customer's surgery on their back on the nineteenth. Thank you for choosing and trusting t e with your plumbing needs

Troubleshooting, smoke detector replacement upstairs hallway.

On today’s visit I met with the homeowner. The homeowner expressed an issue with a clogged lavatory sink drain. I took a look and put together estimates to perform work. Once I received approval I took a part the p trap and pop up assembly and removed hair and sink gunk. I put everything back together and tested for restoration flow. The sink is back drain properly at this time with no leaks. Thanks for choosing TE certified plumbing!

The panel had several breakers installed that were a different brand or model than the panel manufacturer intended. While different brands of breakers can sometimes physically fit into the same slots, they do not seat perfectly on the internal bus bar. This loose fit creates poor electrical contact, which can lead to overheating, arcing, and a failure to trip properly during an electrical overload. To ensure your system is safe, fully compliant with the National Electrical Code (NEC), and covered by manufacturer warranties, I have replaced those mismatched breakers with the exact factory-approved models specified for your panel.

For this job, I completed a troubleshoot for several issues in the home. I replaced a few bulbs and found why a bath fan was not working. Thank you for choosing TE Certified Electricians!