Milton, GA Electrician, Plumber & HVAC Services

Upon arrival to the dugout club, both thermostats were set in cool mode at 75 degrees but the temperature was lower than the set point temperature. Lowered the temperature for both thermostats and both systems engaged cooling mode. Both systems appear to be cooling within parameters at this time. Client stated unit 1 was not engaging as it is today. Previous HVAC service observed the breakers tripping for the systems due to weak breakers. A circuit breaker was replaced today by our electricians and this must have resolved the issue. Unit 1 condenser coil is heavily impacted with grass and it should be cleaned to allow proper operational efficiency. Make sure filters are being replaced every 3 months to avoid problems with your HVAC systems.

Troubleshoot lights not working, air handler not working

Added Apco x ultras to each system in home, tested system. Apco functioning as designed. System operational. Flushed and drain line. Drain not clogged.

Concerns of emergency heat not shutting off. Tested emergency heating, standard heating and cooling via thermostat in the main dining area. No issues noticed. Cycles turning on and off normally at this time. No immediate issues noticed. Thank you for choosing TE certified!

Replace two floodlights on front and back corner of the house

Full system installed for upstairs with: New safety switches New whip New smart thermostat New drain pan New outdoor pad Flue mods

Installed Streamlabs Control smart water valve. Went through the set up and calibration steps. Unit is working as it should! Discussed the functions and expectations with the customer. Replaced tub drain and stopper in the upstairs bathroom. Thank you for choosing TE Certified!

I was called out today because the system stopped cooling after refrigerant was added during the previous visit. At that visit, the homeowner’s husband chose to add refrigerant and declined the recommended nitrogen leak search. Upon arrival today, I found the system completely out of refrigerant. I added some R-410A to perform a complimentary leak search and found the evaporator coil rusted and leaking. The customer expressed frustration regarding the repair costs and requested a detailed labor breakdown. I provided a quote to replace the leaking evaporator coil and repair the system. Thank you for choosing TE Certified.

Shut down water heater. Remove existing flammable vapor sensor assembly and install new sensor. Test and verify operation. Also install new AO Smith burner door

Remove and replace customer provided light fixtures

● Inspected and corrected electrical connections previously installed using backstab and other improper termination methods. ● Re-terminated applicable devices using secure, professional wiring methods to improve connection reliability and long-term electrical safety. ● Corrected loose, improperly seated, and misaligned devices to ensure a secure, level, and flush installation. ● Inspected existing devices for visible deficiencies and addressed issues identified during the process. ● Installed two whole-home surge protective devices to provide additional protection against electrical surges. ● Installed a new Lutron Caseta Smart Hub for home lighting automation and connectivity. Remaining Work (Scheduled Return Visit): ● Provide power to an existing switch location, with No access. ● Install two new electrical panel covers. ● Complete professional circuit identification and labeling for both electrical panels.

For this job, I worked on replacing two bad switches and rewiring two fluorescent lights to bypass the ballast.

Today we replaced the flapper, fill valve, and supply line for the downstairs guest bathroom toilet. Tested thoroughly ensuring no leaks and proper function. Cleaned up work area. This is a no warranty repair

For this job, I did a leak search for the homeowner. During my walk-through, I noticed that the meter only spun when the master irrigation valve was open. However, when we close the master irrigation valve, the meter stop spinning and not far from the master irrigation box we found the busted zone valve that was causing the Issue

Arrived to complete work as per estimate. Turned water off to the home and drained down system. Disconnected water lines (recirculating and cold water inlet for tankless water heater). Fabricated new water lines and installed check valves in the proper orientation for each. Restored water to the home and tested for leaks, no issues at this time. Replaced a drip leg assembly comprised of black iron fittings on the unit. Fittings had signs of weathering (rust/corrosion), and while not functionally affected homeowners elected to proceed with replacement. Reconnected gas whip connector and restored gas to unit. Turned water heater back on, and walked home bleeding air out of system and checking for proper function at all fixtures. No further issues at this time. Thank you for being a valued HomeCare Member! Sincerely, Brandon Smith T.E. Certified | Plumbing Service HALO Certified | Water Expert Direct Cell: (770) 430-7558 License No: 507926

Summary of Visit: Received call regarding leak in basement ceiling. Upon arrival, homeowner informed me that the dishwasher and/or garbage disposal had been running when they noticed the issue forming (previous evening). Before engaging with kitchen sink, performed due diligence in testing of whole home water pressure. Once appropriate pressure range was confirmed, tested kitchen sink to ascertain cause of leak. Immediately discovered that any water run through the sink would leak directly through the bottom of the garbage disposal (it had long since rusted out). Because the dishwasher drain runs through the disposal, this effect would occur when the former was in use as well. While in the course of thorough evaluation, noticed that both water heaters serving the home were approaching 18 years (about double the average useful life of these machines). Also noted lack of hammer arrestor underneath kitchen sink, multi-turn stop on CPVC line feeding dishwasher, and polyvinyl supply

Replaced three toilets in the house. Also replaced all three straight stops and supplies to the toilets. Turned on water and checked all toilets to ensure proper functioning

We were called out due to a leaking expansion tank and temperature and pressure relief valve on the 8 year old water heater. We gave repair and replacement options and the customer chose to have us repair the existing water heater. We replaced the relief valve, the expansion tank and raised the relief line on the exterior to above ground level.

Replaced the supply plenum. Replaced damper. I replaced the bypass and set it to .5 inches of water column. I added slope to the drain line. I added a clean out T. I flushed the drain line. I tested the zoning and verified that the system was operating when I left. The drain line was strapped and secured. Emailed estimate for better flood protection.

The sump pump located on the basement bedroom closet had stopped working the breaker would not reset. They moved the sump pump over to the bedroom circuit, plugged it in and then lost power to the bedroom. The sump pump circuit is a dedicated 20 amp that is wired correctly and is located in panel “A” or the left panel, #10 on the panel board. After resetting the breaker I counted “6” blinks from the breaker indicating that the safety feature had failed and that a replacement of the breaker would be needed. After installing a new breaker, testing the safety feature I plugged the sump pump back in and attached my amp probe around the wiring and turned the breaker back on. The reading I was getting was 7.8 amps. Inside the bedroom is a GFCI outlet just left of the bedroom door in the basement. This device had tripped when plugging the sump pump in. I informed the homeowner that there could be an issue with the sump pump and if the breaker continues to trip then the motor would need to b

Battery replacement on Generac home standby generator

Today we were called out because the homeowner had an issue with their breaker for their kitchen lights constantly tripping. After performing troubleshoot, I found that the middle light fixture was twisted and pinched the hot and neutral wire on the light. Today we performed a troubleshoot and removed the light fixture. I tested everything and it was on and working thank you for choosing TE certified!

Install vanity with drainage tied in, shower trim, and vent cover Discounted money from a previous line item I entered twice by mistake

after doing a thorough troubleshoot, like a load calculation for the subpanel running heavy loads on the subpanel to stress out the system, I could not physically get the two pole hundred amp sub panel breaker to trip on site. I did a thorough continuity test for the wiring feed and everything checked out safely and properly left an estimate for a breaker replacement in the off chance this breaker is starting to fail, but again could not get the breaker to fail on site.

Installed two toilet flanges, two skirted toilets with one bidet seat, shower trim, 6 water valves for the fixtures, drainage underneath bathroom sink, two widespread faucets and will return Monday to install vanity/drainage/shower trim in other bathroom.