Milton, GA Electrician, Plumber & HVAC Services

Came out to a failed vacuum breaker on a hose bib on the left side of the house replaced the vacuum breaker

Replaced leaking 20 year-old 40 gallon lowboy electric water heater and also 20 year-old pressure regulating valve. New water heater installed included all brand, new copper piping, shut off valve, expansion tank, and strap, and new aluminum water heater pan with leak alarm. Replaced old PRV with brand new AUB PRV, PRESSURE SET TO 70 PSI EVERYTHING TESTED TO ENSURE PROPER FUNCTION.

Install customer supplied cartridge in kitchen spray rinse faucet and verify temperature stays consistent throughout kitchen.

Cut out section of slab to dig down and cut out old leaking yard hydrant. Slightly reroute waterline upward for easier access with new shut off valve and newly installed hydrant. Supported with cement in ground, irrigation box and gravel installed for hydrant drain down, spout and new irrigation box. Also install installed for easy access shut off valve to hydrant. Report concrete in area where work was complete complete.

Today I came out for 2 system Home Care. I inspected all electrical components, checked gas pressures, static pressures, blower wheel, evaporator coils, heat exchangers, duct work, cleaned flame sensor, cleaned inducer draft tubing, changed the filter, and cleared drain lines. System 1 is a 2026 Carrier furnace located in basement servicing main area. Blower wheel has some debris building up on fan blades. There is no secondary drain pan under the furnace or under the condensation pump. There is no flood protection of any kind on unit. Condenser coils are getting debris built up on coils. System 2 is a 2024 Rheem furnace located in attic servicing upstairs. Blower wheel and evaporator coils have debris built up on them. There is no primary flood protection on drain line. Drain line is starting to form a belly. Condenser coils have debris built up on them. After going over all findings and options, customer would like to move forward with adding float switch to upstairs unit, drai

Install two light additions in dining room location (4 inch wafer lights) Replace existing light with 4 inch wafer LED light Install dimmer switch in dining room location Replace 6 inch lights in daughter’s upstairs bedroom with wafer led lights Install dimmer switch in daughter’s upstairs bedroom Replace three breakers in electrical panel (eaton Cutler hammer generation two) Replace two additional breakers in sub panel that are not operating as intended. We tested these breakers while replacing the three the customer brought to our attention.

Redevice home and smoke detectors Install whole home surge protector

Panel Cover Restoration: 2 New Panel Covers With Typed Out Labeling. Ran Power to Breakfast Area Lutron Smart Switch.

Performed 2 system Homecare maintenance today. Filters did not require replacement today. Drain lines have been flushed and are clear at this time. All heat and cool operations are within parameters at this time. It is recommended to upgrade your flood protection devices for the UL system to reduce the risk of flooding in the event of a clogged drain back up or if system freezes to a refrigerant leak developing. The evaporator coil appears to have been replaced once already, observed by its date code of 2018. Lennox is known for its coils leaking. The compressor is pulling high amps at 14.8 and the capacitor is outside of tolerance. The cooling system is working harder than it should for acceptable efficiency so it’s using more energy than it should to cool properly. This UL system was installed 16 years ago and has expired its life expectancy. Investing in a new system would be recommended before the next expensive repair. Replaced dual capacitor for UL unit today.

Homeowner has extensive water damage in the garage. She had a plumber come out from another company. Told her it was condensation from the HVAC equipment. I verified that it was not coming from our equipment, observed no water leakage in the attic where another unit was located. Used my moisture detector to pinpoint the source of the leak. Homeowner has a leak somewhere between the dishwasher and the sink. Homeowner has used the dishwasher in the last 24 hours. Due to the considerable amount of moisture, I believe a pipe has burst within the wall. TE certified is sending a plumber out to pinpoint the source of the leak.

Replace two existing chandeliers No crystals Existing dimmer switches

I performed a minor toilet rebuild, which included the fill valve, flapper, handle and supply line. I tested my work thoroughly to ensure proper function

Replace chandelier in breakfast area Conduct troublshoot in basement location

Upon arrival to the dugout club, both thermostats were set in cool mode at 75 degrees but the temperature was lower than the set point temperature. Lowered the temperature for both thermostats and both systems engaged cooling mode. Both systems appear to be cooling within parameters at this time. Client stated unit 1 was not engaging as it is today. Previous HVAC service observed the breakers tripping for the systems due to weak breakers. A circuit breaker was replaced today by our electricians and this must have resolved the issue. Unit 1 condenser coil is heavily impacted with grass and it should be cleaned to allow proper operational efficiency. Make sure filters are being replaced every 3 months to avoid problems with your HVAC systems.

Troubleshoot lights not working, air handler not working

Added Apco x ultras to each system in home, tested system. Apco functioning as designed. System operational. Flushed and drain line. Drain not clogged.

Concerns of emergency heat not shutting off. Tested emergency heating, standard heating and cooling via thermostat in the main dining area. No issues noticed. Cycles turning on and off normally at this time. No immediate issues noticed. Thank you for choosing TE certified!

Replace two floodlights on front and back corner of the house

Full system installed for upstairs with: New safety switches New whip New smart thermostat New drain pan New outdoor pad Flue mods

Installed Streamlabs Control smart water valve. Went through the set up and calibration steps. Unit is working as it should! Discussed the functions and expectations with the customer. Replaced tub drain and stopper in the upstairs bathroom. Thank you for choosing TE Certified!

I was called out today because the system stopped cooling after refrigerant was added during the previous visit. At that visit, the homeowner’s husband chose to add refrigerant and declined the recommended nitrogen leak search. Upon arrival today, I found the system completely out of refrigerant. I added some R-410A to perform a complimentary leak search and found the evaporator coil rusted and leaking. The customer expressed frustration regarding the repair costs and requested a detailed labor breakdown. I provided a quote to replace the leaking evaporator coil and repair the system. Thank you for choosing TE Certified.

Shut down water heater. Remove existing flammable vapor sensor assembly and install new sensor. Test and verify operation. Also install new AO Smith burner door

Remove and replace customer provided light fixtures

● Inspected and corrected electrical connections previously installed using backstab and other improper termination methods. ● Re-terminated applicable devices using secure, professional wiring methods to improve connection reliability and long-term electrical safety. ● Corrected loose, improperly seated, and misaligned devices to ensure a secure, level, and flush installation. ● Inspected existing devices for visible deficiencies and addressed issues identified during the process. ● Installed two whole-home surge protective devices to provide additional protection against electrical surges. ● Installed a new Lutron Caseta Smart Hub for home lighting automation and connectivity. Remaining Work (Scheduled Return Visit): ● Provide power to an existing switch location, with No access. ● Install two new electrical panel covers. ● Complete professional circuit identification and labeling for both electrical panels.

For this job, I worked on replacing two bad switches and rewiring two fluorescent lights to bypass the ballast.